Multi-Function AUTO Emergency Start Power-15000mAh
Multi-Function AUTO Emergency Start Power-15000mAh
** What should you do if your drop anchor on the highway or can't start in the cold weather?
** What should you do if your mobile no power when you are out of door?
** What should you do if your laptop no power when you are negotiating customer about a big order?
Don't worry right now, my mini portable jump starter can solve your emergency issue.
CAUTIONS:
To avoid cause accidents, make sure note the following cautions:
1. Take off the main unit within 30 seconds after starting the car.
2. Don't clip the two terminals at the same end on the battery.
3. Don't Disassemble the unit!
Product Highlights:
* The smallest and lightest portable power with patented technology in the current market.
* Use high capacity high power polymer cells, fast charging and low self-discharge, cycles can reach 1000 times.
* Support 12V car for emergency start, portable illumination and various mobile phone, PSP, MP3/MP4.
* Pocket PC PDA, notebook as well as other products charge / power supply.
* Multiple safety protection design to ensure the product has zero defect.
Instructions for use:
1, Select the appropriate voltage and connector for the electronic device to charge / power supply
2, Press the switch to start charging when your device connected with EPOWER; If you unplug the cable, auto-sleep will start in one minute.
3, Five lights will flash circularly during the charging by EPOWER and all lights will keep bright when your device is full-charged.
4, During the charging for your device, LED lights indicate the balance power of built-in battery of EPOWER. Four lights indicate 80% balance, three lights indicate
60% balance, two lights indicate 40% balance and one light indicates 20% balance. The built-in battery is empty when all LED lights start to flash.
5, Press the switch five seconds to start If you want to use LED for illumination and select the status ( light, strobe, SOS, close) by pressing the switch to transform.
6, Store the product in a cool and dry place and away direct sunlight.
Special note:
To start 12V car, please make sure at least two LED lights of EPOWER are bright firstly, then connect the red battery clip to the battery positive (+) and black clip to
the battery negative (-) and insert the plug into the EPOWER, finally turn the ignition switch to the START position. Once the car is started, please disconnect the
plug and remove the battery clips immediately.
Product parameter:
Output voltage at auto start end 12V
Dimension: 165*79*40mm
Capacity: 15000mAh
Output for vehicle: 12V
USB output: 5V/2A
Input: CC/CV 15V/1A
Start current: 200A
Peak current: 400A
Battery life: 3000 times
Operating temperature: 0~85 C
1. LED illumination light
2. 19V voltage output indicator light
3. 16V voltage output indicator light
4. 12V voltage output indicator light
5. 12/16/19V---2A/3A/3.5A outlet
6. Electrical quantity indicator light
7. Key switch
8. USB 5V--- 2A outlet
9. 15V--- 1A charge inlet
10. Master switch
11. 12V--- 200A auto start outlet
Correct operation flow for auto start:
Parts List:
1. Mobile power * 1pc
2. Cell phone adapter cable * 1pc
3. The notebook adapter cable * 1pc
4. The notebook interface * 8pcs
5. 220 v Charger * 1pc
6. Car charger * 1
7. Battery clip * 1
8. SuperOBD bag *1
- what is the difference between tacho pro 2008 and digiprog3
2016-07-14 - New tool OBDSTAR PRO3 for immo and odometer correction
2016-07-13 - the software of HDD for vas5054 can not be copied
2016-07-12 - vas5054 full chip with OKI and bluetooth
2016-07-11 - hand baby/Cbay open G function
2016-07-10 - the active of FVDI2
2016-07-07 - Launch X431 GDS 12-24V English Diesel Diagnostic Configuration Heavy Duty
2016-07-06 - X100 PAD original key programmer of xtool
2016-07-05 - the code of digiprog3 odometer correction
2016-07-04 - New MB SD Connect Compact 4 with UDS diagnose protocol
2016-07-03
Email: sale@car2diag.com
MSN: sale@car2diag.com
SKYPE: autocables
SKYPE: car2diag03