Auto Programmer

UPA- USB FULL With Adapters upa programer,ups usb,upa programmer,upa pro .

Motorola 9s12 Programmer Motorola MC68HC912/MC68HC9S12 ETL MOTO9S12 Motorola MC68HC912/MC68HC9S12 Flash/EEPROM programmer with security passed

In circuit / on board EEPROM programming. Communication with PC via a serial port CONFIG Register Programming Pin tester in both operation modes

Motorola MC68HC908AZ60, MC68HC05H12 Programmer Flash/EEPROM programmer with security passed On board EEPROM/FLASH programming. Communication with PC via a LPT port. High - Speed EEPROM/FLASH programming 64QFP ,100QFP and 52PLCC programming adapters

MOTOROLA MC68HC705B16/32, MC68HC705X16/32, MC68HC05B6/8/16/32, MC68HC05X16/32 SMART EEPROM Programming Tool

The TMS370 is the best low cost programmer for TI TMS Microcontroller development, car radios and car dashboards programming. A serial port interface (COM1, COM2) connects the programmer to any desktop or laptop PC running Windows 98/2000/XP.

COM connector and support USB connector as well, Mileage correction reset your the mileage by directly input the data; Works on CPUs use NEC board, support userself upgration.

BMW M35080 Programmer List of supported vehicles: E38 E39 E46 E46 BOSCH E83 E65

X PROG-M full authorization The XPROG-m programmer is designed to replace the earlier version of XPROG programmer. XPROG-m programmer is fully upward-compatible hardware with XPROG programmer and have many additional features

80D0WQ ERASER Programmer D80DOWQ programmer,D80D0WQ Eraser,ETL D80D0WQ D80D0WQ ERASER/Programmer: Easy to use Windows 98/2000/XP software: Read, Program, Erase Incremental Registers\EEPROM Erase time 5-10 minutes

Easy to use Windows 98/2000/XP software:

ELNEC BEEPRO + Short description: 50825 supported devices by 2.64 version of SW (5. Nov. 2009) very fast programming, one of the fastest programmers in this category. Programs 64-Mbit NOR Flash memory less than 46 seconds and 1Gbit NAND Flash less than 120 sec.

supported more than 30,000 devices

This Tool is a frequency sweeper with 5V square wave output (Duty cycle 50%, effective frequency range from over 10kHz (max 50kHz) to 50Hz) .This tool can be also considered as a MCU version of the software TMS-374 Decoder ECU. The only difference between the two tools is that the MCU version works without a PC.

The XPROG-m auto programmer is designed to replace the earlier version of XPROG programmer. XPROG-m programmer is fully upward-compatible hardware with XPROG programmer and have many additional features.

SH 705X programmer include all function for reading renesas RENESAS mcu ,like 64F7055 64F7058 64F7059.those mcu often use in HONDA .MAZDA,NISSAN and a lot of car.

Serial suite Piasiniengineering v4.1 master

UPA-USB programming adapter set is an adapter set for UPA-USB programmer ,you can do much more work with it ,Device configuration is done over special config keys which make the work convenient and safe compared to wiring up all manually.

CS LabTool48UXP Programmer ,features universal pin driver , fast programming speed,can Read, blank check, device insertion/ contact check, verify, checksum, EPROM ID check, compare, erase chip, function test, program, memory protect, device configuration setting, device search...

Upa-usb 2013 is the full set with all adapters,Device configuration is done over special config keys which make the work convenient and safe compared to wiring up all manually.